hanging monitor on lath and plaster walls

#Hanging monitor on lath and plaster walls install
#Hanging monitor on lath and plaster walls Patch

Although in future you should consider recessing the back of your cabinets 3/4 of an inch and using a French in such situations. (Each cabinet is custom, like a piece of furniture.) The heaviest cabinet is about 30 pounds when empty.

#Hanging monitor on lath and plaster walls install

If you recessed the backs of your uppers, then install a (hardwood) hang cleat to the wall studs and attach your boxes to the cleat.Ĭan you attach cabinets to a French cleat? Assuming the cleat on the wall is very secure - this is for a custom job where the owner wants to take them with him when he moves. I wouldn't want to be the guy in the future trying to remove and save the cabinet for use elsewhere. Cabinet's not going anywhere any time soon. Screw the ones to the studs that you can, screw the rest to the lath and plaster with adhesive caulking under all of them. You are making mountains out of mole hills. What contributor D said, if it's applicable. Gang 'em together to make one 48' cabinet, and screw it in wherever you can. If that 9' cab is touching the pantry and one of the middle 15' cabinets, which I assume will be securely mounted to studs on down the row, just attach it to those two cabinets. If going through 3/4 mounting strip, don't use anything shorter than 2 1/2'. They have a larger washer head and an auger tip. Your screw length will depend on your mounting rail or if you are just screwing through the backs. Let the customer know the situation ahead of time and they will understand. Also, screw the cabinets to the pantry cabinet if possible. Pocket screw a 2x4 in between the studs, fill out to the thickness of the wall panel, hang your cabinets on the 2x4. (Cabinet and Millwork Installation Forum)Ĭut the lath and plaster back the width of a 2x4 and the length you need at the top of where the cabs will mount. I'm in the middle of trying to get this done before putting base cabinets under these. Suggestions? Fastener recommendations and lengths? And of course. Any way I juggle them, the edge of the 9' cabinets falls on a stud, leaving the in a stud-free zone, and the 15's won't have more than one set of attachment points, top and bottom.Īfter pondering a while, I'm thinking I need to install a couple of 1 x 2 horizontal mounting rails through the wall to the studs, screw the cabinets to the rails and then hide the gap with molding or something similar. The next stud to the right is 9' from the edge of the pantry. This set of cabinets starts to the right of an 18' wide pantry cabinet. The cabinets are all 30' tall and 12' deep, with two 9' wide cabinets at each end and two 15' wide cabinets in the middle. Be as thorough as possible.I'm trying to hang a set of four cabinets on a lath and plaster wall.

Use a dry non-abrasive washcloth to wipe away all the moisture on your wall, using a circular motion again.

Rinse the cloth in warm water, then use it to wipe away any soap residue on the wall.

Rub the area of your wall down with your soapy cloth.

#Hanging monitor on lath and plaster walls Patch

Work the soap into a small patch of suds on the cloth. Soak a non-abrasive washcloth in warm water, then place a bead of mild soap on the cloth.There are a few different ways you can clean plaster, but the simplest is to use warm water and mild liquid dish soap.As such, drying the wall after washing it is twice as important.

Thoroughly drying the wall is important for the sake of the adhesive, but plaster is also fairly porous, so mildew and similar problems may develop if you allow it to stay damp.

Adhesive glue will not stick to a surface that is dirty or dusty.

Dry the plaster thoroughly when finished. Before you attach an adhesive to a plaster wall, you need to clean the surface of the plaster to strip away any oils and dirt. Note that there are also anchors made from fiber, wood, and metal, however, so you have a range of options to choose from.

Plastic anchors are among the most common and will usually suffice for this project.This sleeve also minimizes the amount of stress put on the plaster. As a result, the screw will sit more securely inside the wall. Wall anchors consist of a sleeve that expands into the wall once you drive a screw into it.Note that the anchor should also be flush with the wall.The anchor needs to be snug and straight inside the wall. If the anchor starts bending, you should take it out and make the hole a little larger. If your hole is not large enough, a plastic anchor will bend.Remove the tape covering your hole before hammering the anchor inside.Tap the anchor into the hole, using just enough force to drive it in without bending the anchor or cracking the wall. Place the anchor directly over the hole in your wall.